Connector and cables Sample Clauses

Connector and cables. ‌ REQ-033762/A REQ-033763/A REQ-033764/A REQ-033774/A The positioners shall be equipped with vacuum compatible cables and vacuum compatible push-pull connectors (e.g. LEMO connector or equivalent) for connecting to the extension cable. Positioner cable shall be at least 120 xx xxxx. The extension cable shall be 200 xx xxxx. NOTE: Extension cables should be ended by vacuum compatible push- pull connectors (e.g. LEMO connector or equivalent) on one side and vacuum compatible 15-pin D-SUB connector on the other side to be connected to feed-through flange from vacuum side to air side. The positioners shall be equipped with an integrated optical position sensor to measure the absolute position of the positioner. A description of cable wires or connector pins, including piezo motor electrical characteristics and time sequence of the piezo motor driving signals, shall be included in the accompanying technical documentation. The dual channel controllers shall be Euro-size format modules with DIN41612-C connector for insertion into the 19-inch rack mount chassis provided. The chassis shall support at least six dual channel controller modules. Only one chassis is required. Each controller shall provide an RS232 serial interface and a low-level interface together in a high-density D-SUB-26 connector for each axis. The low-level interface shall provide Step, Direction and Enable control inputs, and Positive Limit, Negative Limit and Home control outputs, compatible with TTL logic, and quadrature A, B and Z differential position outputs, compatible with RS422 electrical standards. The serial interface shall provide basic control and status via an ASCII-based command set provided with the documentation.
AutoNDA by SimpleDocs

Related to Connector and cables

  • Meter and Cabling Be obliged to draw electricity lines/wires, television cables, broadband data cables and telephone cables to the said Apartment only through the ducts and pipes provided therefor, ensuring that no inconvenience is caused to the Promoter or to other apartment owners. The main electricity meter shall be installed only at the space designated for common meters. The Allottee shall under no circumstances be entitled to affix, draw or string wires, cables, dish antennae or pipes from, to or through any part or portion of and outside walls of the building in which the Apartment is located save in the manner indicated by the Promoter/Association (upon formation).

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Switching All of the negotiated rates, terms and conditions set forth in this Section pertain to the provision of local and tandem switching.

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.

  • Generators Temporary installation of generators, and permanent installation of generators that are placed inside existing non-residential buildings or that occupy an area under 50 square feet behind the building they serve.

  • Moonlighting 24.01 The Company and the Union agree in principle to eliminate the practice commonly referred to as moonlighting.

  • Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.

  • Connectivity User is solely responsible for providing and maintaining all necessary electronic communications with Exchange, including, wiring, computer hardware, software, communication line access, and networking devices.

  • ELECTRICAL SERVICES A. Landlord shall provide electric power for a combined load of 3.0 xxxxx per square foot of useable area for lighting and for office machines through standard receptacles for the typical office space.

  • Systems The details of any systems work will be determined after a thorough business analysis. System's work will be billed on a time and material basis. Investors Bank provides an allowance of 10 systems hours for data extract set up and reporting extract set up. Additional hours will be billed on a time and material basis.

Time is Money Join Law Insider Premium to draft better contracts faster.