Common use of Collection Equipment Clause in Contracts

Collection Equipment. The Contractor shall have on hand at all times and in good working order such equipment as shall permit the Contractor to adequately and efficiently perform the contractual duties specified in this Agreement. Upon execution of this Agreement and annually thereafter, the Contractor shall provide, in a format specified by the Contract Administrator, a list of the equipment to be used by the Contractor to provide services relating to this Agreement. Solid Waste and Recycling Collection equipment shall be of the enclosed loader packer type, or other equipment that meets industry standards and is approved by the Contract Administrator, unless otherwise provided within this Agreement. All Equipment shall be kept in good repair, appearance and in a sanitary, clean condition at all times. The County has the right to inspect collection equipment during collection routes. Equipment utilized for Collection of Recyclable Materials shall be clearly identified for that purpose. The Contractor shall have available reserve equipment which can be put into service within two (2) hours of any breakdown and a prompt notifications shall be provided to County staff. Such reserve equipment shall correspond in size and capacity to the equipment used by the Contractor to perform the contractual duties. If the public road or public right-of-way in the Service Area is substandard, as specifically designated by the Contract Administrator, in writing, the Contractor must provide lightweight equipment to service these roads (i.e., gross vehicle weight not to exceed 15 tons). Service on these substandard roads shall be a minimum of one combined Solid Waste and Vegetative Waste Collection and one separate Recycling Collection per week. In the event that Solid Waste designated to be disposed of at the Resource Recovery Facility has to be disposed of at the a landfill, the Contractor shall make arrangements to keep tires separated from other Solid Waste. The Contractor's vehicles, roll-off Containers, dumpsters and other equipment must be clearly identified with the name, phone number of the company's local office and equipment number on each side of the equipment and the equipment identification number shall also be on the front and rear of each vehicle. The Contractor shall allow commercial customers to select either top loading or side loading 6 and 8 cu. yd. dumpsters and shall provide the type requested by the commercial customer. All vehicles utilized for the Collection of Recyclable Material shall be clearly identified for that purpose. Letters and numbers shall be at least six (6) inches high and of proportionate width unless otherwise approved by the Department. This identification shall be affixed to each vehicle and piece of equipment. The Contractor shall provide a list of equipment used in the service area, including equipment number. All vehicles shall be kept clean (i.e., washed at least once per week), in sanitary condition, good repair and meet community standards of appearance at all times. The County shall be the sole judge of community standards of appearance. At a minimum, all Compactors, and other Contractor owned Containers are to be cleaned (washed) and sanitized as needed or when requested by the County, or at least twice annually. The noise level for the Collection vehicles during the stationary compaction process shall not exceed seventy-five (75) decibels at a distance of twenty-five (25) feet from the Collection vehicle and at an elevation of five (5) feet from the horizontal base plane of such vehicle. All vehicles, Containers (except roll-offs), transfer trailers, etc. shall have enclosed tops and such tops and/or tarps shall remain closed while a vehicle is in motion.

Collection Equipment. A. The Contractor shall have on hand at all times and times, in good working order order, such collection equipment as shall permit the Contractor to adequately and efficiently perform the contractual duties specified in this Agreement. Upon execution of this Agreement and annually thereafter, Any proposed change in the Contractor shall provide, in a format specified by the Contract Administrator, a list of the equipment to be collection system being used by the Contractor during the Agreement period shall be submitted in writing by the Contractor to provide services relating the Administrator. B. Collection vehicles shall be of a type sufficient to efficiently collect all Solid Waste, Bulk Waste, and Program Recyclables covered by this Agreement, and transport such materials to the Designated Facilities in a manner such that no collected materials can be blown or fall from the vehicle during transport. The Contractor may utilize open-bed vehicles in the provision of Bulk Waste Collection; however, the vehicles must contain the Bulk Waste so that no material is spilled, leaked, or blown from the vehicle, and the vehicle must be covered with a securely fastened tarp during transport. C. Each collection vehicle shall be equipped at all times with: (a) all safety supplies, equipment, and first aid supplies required by applicable laws; (b) a fire extinguisher; (c) a heavy-duty broom, a rake, and a large dustpan; (d) a spill response kit; (e) an audible back-up warning device; and (f) back-up cameras. The spill response kit shall be suitable and adequate for cleaning up any leaks or spills of oil, hydraulic fluid, or other liquids from Franchisee's collection vehicles. D. All equipment shall be kept well painted, shall clearly display, and shall only display Contractor's name, telephone number, and the materials being collected in the vehicle for Residential Solid Waste and Recycling Collection equipment Residential Program Recyclables; and shall be of the enclosed loader packer type, or other equipment that meets industry standards and is approved by the Contract Administrator, unless otherwise provided within this Agreement. All Equipment shall be kept maintained in good repair, appearance appearance, and in a sanitary, clean condition in order to meet community standards of appearance at all times. The County has If the right Contractor intends to inspect use the same vehicles to collect Solid Waste and Program Recyclables, a magnet sign on the vehicle to indicate which Collection Service is being provided will suffice to satisfy the requirement to display which Residential Collection Service is being conducted (i.e., Solid Waste or Program Recyclables). All collection equipment during collection routes. Equipment utilized for Collection of Recyclable Materials shall be clearly identified leak-proof so as to prevent any liquid from draining onto the ground. The Town reserves the right, at its discretion, to require a vehicle be taken out of service for habitual leakage of oil, hydraulic fluid, or other liquids or other maintenance issues. Such vehicle shall not be placed back into service until and unless the Town is able to verify that purpose. the necessary repairs have been made. E. The Contractor shall have available to it, at all times, reserve equipment which can be put into service and operation within two (2) hours of any breakdown and a prompt notifications shall be provided to County staffbreakdown. Such reserve equipment shall correspond in size and capacity to the equipment used by the Contractor to perform the contractual duties. If the public road or public right-of-way in the Service Area is substandard, as specifically designated by the Contract Administrator, in writing, the Contractor must provide lightweight equipment to service these roads (i.e., gross vehicle weight not to exceed 15 tons). Service on these substandard roads shall be a minimum of one combined Solid Waste and Vegetative Waste Collection and one separate Recycling Collection per week. In the event that Solid Waste designated to be disposed of at the Resource Recovery Facility has to be disposed of at the a landfill, the Contractor shall make arrangements to keep tires separated from other Solid Waste. The Contractor's vehicles, roll-off Containers, dumpsters and other equipment must be clearly identified with the name, phone number of the company's local office and equipment number on each side of the equipment and the equipment identification number shall also be on the front and rear of each vehicle. The Contractor shall allow commercial customers to select either top loading or side loading 6 and 8 cu. yd. dumpsters and shall provide the type requested by the commercial customer. All vehicles utilized for the Collection of Recyclable Material shall be clearly identified for that purpose. Letters and numbers shall be at least six (6) inches high and of proportionate width unless otherwise approved by the Department. This identification shall be affixed to each vehicle and piece of equipment. The Contractor shall provide a list of equipment used in the service area, including equipment number. All vehicles shall be kept clean (i.e., washed at least once per week), in sanitary condition, good repair and meet community standards of appearance at all times. The County shall be the sole judge of community standards of appearance. At a minimum, all Compactors, and other Contractor owned Containers are to be cleaned (washed) and sanitized as needed or when requested by the County, or at least twice annually. The noise level for the Collection vehicles during the stationary compaction process shall not exceed seventy-five (75) decibels at a distance of twenty-five (25) feet from the Collection vehicle and at an elevation of five (5) feet from the horizontal base plane of such vehicle. All vehicles, Containers (except roll-offs), transfer trailers, etc. shall have enclosed tops and such tops and/or tarps shall remain closed while a vehicle is in motion.

Collection Equipment. The Contractor shall have on hand at all times and in good working order such equipment as shall permit the Contractor to adequately and efficiently perform the contractual duties specified in this Agreement. Upon execution of this Agreement and annually thereafter, the Contractor shall provide, in a format specified by the Contract Administrator, a list of the equipment to be used by the Contractor to provide services relating to this Agreement. Solid Waste and Recycling Collection equipment shall be of the enclosed loader packer type, or other equipment that meets industry standards and is approved by the Contract Administrator, unless otherwise provided within this Agreement. All Equipment shall be kept in good repair, appearance and in a sanitary, clean condition at all times. The County has the right to inspect collection equipment during collection routes. Equipment utilized for Collection of Recyclable Materials shall be clearly identified for that purpose. The Contractor shall have available reserve equipment which can be put into service within two (2) hours of any breakdown and a prompt notifications shall be provided to County staff. Such reserve equipment shall correspond in size and capacity to the equipment used by the Contractor to perform the contractual duties. If the public road or public right-of-way in the Service Area is substandard, as specifically designated by the Contract Administrator, in writing, the Contractor must provide lightweight equipment to service these roads (i.e., gross vehicle weight not to exceed 15 10 tons). Service on these substandard roads shall be a minimum of one combined Solid Waste and Vegetative Waste Collection and one separate Recycling Collection per week. In the event that Solid Waste designated to be disposed of at the Resource Recovery Facility has to be disposed of at the a landfill, the Contractor shall make arrangements to keep tires separated from other Solid Waste. The Contractor's vehicles, roll-off Containers, dumpsters and other equipment must be clearly identified with the name, phone number of the company's local office and equipment number on each side of the equipment and the equipment identification number shall also be on the front and rear of each vehicle. The Contractor shall allow commercial customers to select either top loading or side loading 6 and 8 cu. yd. dumpsters and shall provide the type requested by the commercial customer. All vehicles utilized for the Collection of Recyclable Material shall be clearly identified for that purpose. Letters and numbers shall be at least six (6) inches high and of proportionate width unless otherwise approved by the Department. This identification shall be affixed to each vehicle and piece of equipment. The Contractor shall provide a list of equipment used in the service area, including equipment number. All vehicles shall be kept clean (i.e., washed at least once per week), in sanitary condition, good repair and meet community standards of appearance at all times. The County shall be the sole judge of community standards of appearance. At a minimum, all Compactors, and other Contractor owned Containers are to be cleaned (washed) and sanitized as needed or when requested by the County, or at least twice annually. The noise level for the Collection vehicles during the stationary compaction process shall not exceed seventy-five (75) decibels at a distance of twenty-five (25) feet from the Collection vehicle and at an elevation of five (5) feet from the horizontal base plane of such vehicle. All vehicles, Containers (except roll-offs), transfer trailers, etc. shall have enclosed tops and such tops and/or tarps shall remain closed while a vehicle is in motion.

Collection Equipment. The Contractor shall have on hand at all times and in good working order such equipment as shall permit the Contractor to adequately and efficiently perform the contractual duties specified in this Agreement. Upon execution of this Agreement and annually thereafter, the Contractor shall provide, in a format specified by the Contract Administrator, a list of the equipment to be used by the Contractor to provide services relating to this Agreement. Solid Waste and Recycling Collection equipment shall be of the enclosed loader packer type, or other equipment that meets industry standards and is approved by the Contract Administrator, unless otherwise provided within this Agreement. All Equipment shall be kept in good repair, appearance and in a sanitary, clean condition at all times. The County has the right to inspect collection equipment during collection routes. Equipment utilized for Collection of Recyclable Materials shall be clearly identified for that purpose. The Contractor shall have available reserve equipment which can be put into service within two (2) hours of any breakdown and a prompt notifications notification shall be provided to County staff. Such reserve equipment shall correspond in size and capacity to the equipment used by the Contractor to perform the contractual duties. If the public road or public right-of-way in the Service Area is substandard, as specifically designated by the Contract Administrator, in writing, the Contractor must provide lightweight equipment to service these roads (i.e., gross vehicle weight not to exceed 15 tons). Service on these substandard roads shall be a minimum of one combined Solid Waste and Vegetative Waste Collection and one separate Recycling Collection per week. In the event that Solid Waste designated to be disposed of at the Resource Recovery Facility has to be disposed of at the a landfill, the Contractor shall make arrangements to keep tires separated from other Solid Waste. The Contractor's vehicles, roll-off Containers, dumpsters and other equipment must be clearly identified with the name, phone number of the company's local office and equipment number on each side of the equipment and the equipment identification number shall also be on the front and rear of each vehicle. The Contractor shall allow commercial customers to select either top loading or side loading 6 and 8 cu. yd. dumpsters and shall provide the type requested by the commercial customer. All vehicles utilized for the Collection of Recyclable Material shall be clearly identified for that purpose. Letters and numbers shall be at least six (6) inches high and of proportionate width unless otherwise approved by the Department. This identification shall be affixed to each vehicle and piece of equipment. The Contractor shall provide a list of equipment used in the service area, including equipment number. All vehicles shall be kept clean (i.e., washed at least once per week), in sanitary condition, good repair and meet community standards of appearance at all times. The County shall be the sole judge of community standards of appearance. At a minimum, all Compactors, and other Contractor owned Containers are to be cleaned (washed) and sanitized as needed or when requested by the County, or at least twice annually. The noise level for the Collection vehicles during the stationary compaction process shall not exceed seventy-five (75) decibels at a distance of twenty-five (25) feet from the Collection vehicle and at an elevation of five (5) feet from the horizontal base plane of such vehicle. All vehicles, Containers (except roll-offs), transfer trailers, etc. shall have enclosed tops and such tops and/or tarps shall remain closed while a vehicle is in motion.

Collection Equipment. The Contractor shall have on hand at provide all times equipment necessary for collection, transportation and disposal of Recyclables. Unless the material to be transported presents practical difficulties, all trucks shall be designed and built specifically for Recyclable collection and shall be of the covered all-metal type so the material being collected and transported will not be seen, will not blow, fall or leak from the vehicle. The Contractor shall maintain equipment used in good working order such equipment as shall permit the Contractor to adequately and efficiently perform the contractual duties specified in this Agreement. Upon execution performance of this Agreement and annually thereafter, the Contractor shall provide, in a format specified clean and sanitary condition. A. Hauler of Recyclable Materials must have a license issued by the Contract Administrator, a list City as governed by appropriate City Code. B. The number of the equipment vehicles to be used by the Contractor identifying types, model numbers and capacities must be supplied to provide services relating to this Agreement. Solid Waste the City. C. All vehicles must be maintained in good working conditions, comply with all State inspection requirements and Recycling Collection equipment shall be of the enclosed loader packer type, or other equipment that meets industry standards and is approved by the Contract Administrator, unless otherwise provided within this Agreement. All Equipment shall be kept neat in good repair, appearance and in a sanitary, clean condition at all times. The County has the right to inspect collection equipment during collection routes. Equipment utilized for Collection of Recyclable Materials shall be clearly identified for that purpose. appearance. D. The Contractor shall have available reserve state in the list of truck equipment which can be put into service within two (2) hours of any breakdown how the vehicle design and a prompt notifications operation will meet all City, county, and state load weight limits, including seasonal limitations. The fully loaded gross vehicle weight and weight per axle shall be listed for each of the proposed trucks. E. The number of personnel to be provided to County staff. Such reserve equipment shall correspond in size and capacity to the equipment used by the on each truck must be indicated. F. Contractor to perform the contractual duties. If the public road or public right-of-way in the Service Area is substandard, as specifically designated by the Contract Administrator, in writing, the must identify where collection vehicles will be delivering materials. G. Contractor must be an equal opportunity employer. H. Contractor must provide lightweight equipment to service these roads (i.e.a plan for end use of all collected materials, gross including contaminated materials. I. Contractor must provide a contingency plan in the event a vehicle weight not to exceed 15 tons). Service on these substandard roads or operator is unavailable. J. Vehicles shall be equipped with warning flashers, backup alarms, a minimum broom and shovel for spills, a two-way communication device, and the Contractor’s name and phone number prominently displayed on both sides of one combined Solid Waste and Vegetative Waste Collection and one separate Recycling Collection per weekthe vehicle, along with signs on the back of the vehicle indicating the vehicle makes frequent stops. K. Vehicles must be designated for recyclables collection only. In the event that Solid Waste designated to be disposed of at the Resource Recovery Facility has to be disposed of at the a landfill, the Contractor shall make arrangements to keep tires separated from other Solid Waste. The Contractor's vehicles, roll-off Containers, dumpsters and other equipment All such vehicles must be clearly identified with the namesigned on both sides as a recycling collection vehicle. L. Equipment operators must meet all Federal, phone number of the company's State and local office licenses and equipment number on each side of the equipment and the equipment identification number shall also be on the front and rear of each vehicle. The Contractor shall allow commercial customers to select either top loading or side loading 6 and 8 cu. yd. dumpsters and shall provide the type requested by the commercial customer. All vehicles utilized for the Collection of Recyclable Material shall be clearly identified for that purpose. Letters and numbers shall be at least six (6) inches high and of proportionate width unless otherwise approved by the Department. This identification shall be affixed to each vehicle and piece of equipment. The Contractor shall provide a list of equipment used in the service area, including equipment number. All vehicles shall be kept clean (i.e., washed at least once per week), in sanitary condition, good repair and meet community standards of appearance at all times. The County shall be the sole judge of community standards of appearance. At a minimum, all Compactors, and other Contractor owned Containers are to be cleaned (washed) and sanitized as needed or when requested by the County, or at least twice annually. The noise level for the Collection vehicles during the stationary compaction process shall not exceed seventy-five (75) decibels at a distance of twenty-five (25) feet from the Collection vehicle and at an elevation of five (5) feet from the horizontal base plane of such vehicle. All vehicles, Containers (except roll-offs), transfer trailers, etc. shall have enclosed tops and such tops and/or tarps shall remain closed while a vehicle is in motionoperation requirements.

Collection Equipment. The Contractor shall have on hand at all times and in good working order such equipment as shall permit the Contractor to adequately and efficiently perform the contractual duties specified in this Agreement. Upon execution of this Agreement and annually thereafter, the Contractor shall provide, in a format specified by the Contract Administrator, a list of the equipment to be used by the Contractor to provide services relating to this Agreement. Solid Waste and Recycling Collection equipment shall be of the enclosed loader packer type, or other equipment that meets industry standards and is approved by the Contract Administrator, unless otherwise provided within this Agreement. All Equipment shall be kept in good repair, appearance and in a sanitary, clean condition at all times. The County has the right to inspect collection equipment during collection routes. Equipment utilized for Collection of Recyclable Materials shall be clearly identified for that purpose. The Contractor shall have available reserve equipment which can be put into service within two (2) hours of any breakdown and a prompt notifications notification shall be provided to County staff. Such reserve equipment shall correspond in size and capacity to the equipment used by the Contractor to perform the contractual duties. If the public road or public right-of-way in the Service Area is substandard, as specifically designated by the Contract Administrator, in writing, the Contractor must provide lightweight equipment to service these roads (i.e., gross vehicle weight not to exceed 15 10 tons). Service on these substandard roads shall be a minimum of one combined Solid Waste and Vegetative Waste Collection and one separate Recycling Collection per week. In the event that Solid Waste designated to be disposed of at the Resource Recovery Facility has to be disposed of at the a landfill, the Contractor shall make arrangements to keep tires separated from other Solid Waste. The Contractor's vehicles, roll-off Containers, dumpsters and other equipment must be clearly identified with the name, phone number of the company's local office and equipment number on each side of the equipment and the equipment identification number shall also be on the front and rear of each vehicle. The Contractor shall allow commercial customers to select either top loading or side loading 6 and 8 cu. yd. dumpsters and shall provide the type requested by the commercial customer. All vehicles utilized for the Collection of Recyclable Material shall be clearly identified for that purpose. Letters and numbers shall be at least six (6) inches high and of proportionate width unless otherwise approved by the Department. This identification shall be affixed to each vehicle and piece of equipment. The Contractor shall provide a list of equipment used in the service area, including equipment number. All vehicles shall be kept clean (i.e., washed at least once per week), in sanitary condition, good repair and meet community standards of appearance at all times. The County shall be the sole judge of community standards of appearance. At a minimum, all Compactors, and other Contractor owned Containers are to be cleaned (washed) and sanitized as needed or when requested by the County, or at least twice annually. The noise level for the Collection vehicles during the stationary compaction process shall not exceed seventy-five (75) decibels at a distance of twenty-five (25) feet from the Collection vehicle and at an elevation of five (5) feet from the horizontal base plane of such vehicle. All vehicles, Containers (except roll-offs), transfer trailers, etc. shall have enclosed tops and such tops and/or tarps shall remain closed while a vehicle is in motion.