Common use of By Customer Clause in Contracts

By Customer. Customer shall install, own, operate and maintain all lines, service conductors, meter bases, and equipment, exclusive of Company's meter and meter transformers on Customer's side of the point of delivery and Customer will be the owner and have exclusive control thereof as well also as of all electricity after it passes the point of delivery. Customer shall so arrange his wiring that all electricity for one type of use can be supplied at one point of delivery and measured by a single meter. Except under special circumstances, Company's meter will be located on Customer's side of the point of delivery, and when it is to be so located Customer must make suitable provisions in his wiring for the convenient installation of the type of meter Company will use, and at a place suitable to Company. Customer's service entrance conductors shall not be installed within hollow walls unless the conductors are in conduit. Service entrance conductors not installed in conduit must be readily visible on the source side of Company's meter. Where a socket-type meter is to be used, Customer will provide, install at a place suitable to Company, own, and maintain a meter base or meter/switch enclosure to accommodate Company's meter under the following conditions: (1) the meter base or meter/switch enclosure shall be in accordance with Company specifications and bear the seal of approval of UL or other recognized authority in the industry, (2) Customer agrees to allow Company to install, maintain, and exercise exclusive control over all Company-owned facilities located inside Customer-owned meter base or meter/switch enclosure, including termination of Company-owned conductors to the line side terminals of Customer's meter base or meter/switch enclosure, (3) Customer agrees to allow Company to open and inspect the meter base or meter/switch enclosure at any time, and (4) Customer shall notify Company and obtain permission before altering or performing maintenance inside the meter base or metering section of the meter/switch enclosure. Socket-type meter bases furnished by Company prior to January 1, 1991 will continue to be owned by Company until replacement of meter base is necessary, at which time Customer will provide, install at a place suitable to Company, own, and maintain a replacement meter base under the above conditions. Customer shall not utilize any equipment, appliance, or device which tends to affect adversely Company's supply of service to, or the use of service by, Customer or others. Customer shall not install gaseous discharge lighting with a power factor of less than 90 percent lagging. When polyphase service is supplied by Company, Customer shall control his use so that his load will be maintained in reasonable electrical balance between the phases at the point of delivery. Customer shall install and maintain devices adequate to protect his equipment against irregularities on Company's system, including devices to protect against single phasing.

By Customer. Customer shall install, own, operate and maintain all lines, service conductors, meter bases, and equipment, exclusive of Company's meter and meter transformers on Customer's side of the point of delivery and Customer will be the owner and have exclusive control thereof as well also as of all electricity after it passes the point of delivery. Customer shall so arrange his wiring that all electricity for one type of use can be supplied at one point of delivery and measured by a single meter. Except under special circumstances, Company's meter will be located on Customer's side of the point of delivery, and when it is to be so located Customer must make suitable provisions in his wiring for the convenient installation of the type of meter Company will use, and at a place suitable to Company. Customer's service entrance conductors shall not be installed within hollow walls unless the conductors are in conduit. Service entrance conductors not installed in conduit must be readily visible on the source side of Company's meter. Where a socket-type meter is to be used, Customer will provide, install at a place suitable to Company, own, and maintain a meter base or meter/switch enclosure to accommodate Company's meter under the following conditions: (1) the meter base or meter/switch enclosure shall be in accordance with Company specifications and bear the seal of approval of UL or other recognized authority in the industry, (2) Customer agrees to allow Company to install, maintain, and exercise exclusive control over all Company-owned facilities located inside Customer-owned meter base or meter/switch enclosure, including termination of Company-owned conductors to the line side terminals of Customer's meter base or meter/switch enclosure, (3) Customer agrees to allow Company to open and inspect the meter base or meter/switch enclosure at any time, and (4) Customer shall notify Company and obtain permission before altering or performing maintenance inside the meter base or metering section of the meter/switch enclosure. Socket-type meter bases furnished by Company prior to January 1, 1991 will continue to be owned by Company until replacement of meter base is necessary, at which time Customer will provide, install at a place suitable to Company, own, and maintain a replacement meter base under the above conditions. Customer shall not utilize any equipment, appliance, or device which tends to affect adversely Company's supply of service to, or the use of service by, Customer or others. Customer shall not install gaseous discharge lighting with a power factor of less than 90 percent lagging. When polyphase service is supplied by Company, Customer shall control his use so that his load will be maintained in reasonable electrical balance between the phases at the point of delivery. Customer shall install and maintain devices adequate to protect his equipment against irregularities on Company's system, including devices to protect against single phasing.

By Customer. Customer shall install, own, operate and maintain all lines, service conductors, meter bases, and equipment, exclusive of Company's meter and meter transformers on Customer's side of the point of delivery and Customer will be the owner and have exclusive control thereof as well also as of all electricity after it passes the point of delivery. Customer shall so arrange his wiring that all electricity for one type of use can be supplied at one point of delivery and measured by a single meter. Except under special circumstances, Company's meter will be located on Customer's side of the point of delivery, and when it is to be so located Customer must make suitable provisions in his wiring for the convenient installation of the type of meter Company will use, and at a place suitable to Company. Customer's service entrance conductors shall not be installed within hollow walls unless the conductors are in conduit. Service entrance conductors not installed in conduit must be readily visible on the source side of Company's meter. Where a socket-type meter is to be used, Customer will provide, install at a place suitable to Company, own, and maintain a meter base or meter/switch enclosure to accommodate Company's meter under the following conditions: (1) the meter base or meter/switch enclosure shall be in accordance with Company specifications and bear the seal of approval of UL or other recognized authority in the industry, (2) Customer agrees to allow Company to install, maintain, and exercise exclusive control over all Company-owned facilities located inside Customer-owned meter base or meter/switch enclosure, including termination of Company-owned conductors to the line side terminals of Customer's meter base or meter/switch enclosure, (3) Customer agrees to allow Company to open and inspect the meter base or meter/switch enclosure at any time, and (4) Customer shall notify Company and obtain permission before altering or performing maintenance inside the meter base or metering section of the meter/switch enclosure. Socket-type meter bases furnished by Company prior to January 1, 1991 will continue to be owned by Company until replacement of meter base is necessary, at which time Customer will provide, install at a place suitable to Company, own, and maintain a replacement meter base under the above conditions. Customer shall not utilize any equipment, appliance, or device which tends to affect adversely Company's supply of service to, or the use of service by, Customer or others. Customer shall not install gaseous discharge lighting with a power factor of less than 90 percent lagging. When polyphase service is supplied by Company, Customer shall control his use so that his load will be maintained in reasonable electrical balance between the phases at the point of delivery. Customer shall install and maintain devices adequate to protect his equipment against irregularities on Company's system, including devices to protect against single phasing. If the Customer does not prevent voltage fluctuations detrimental to the service, the Company may require the Customer to either discontinue the operation of the equipment or install the necessary motor-generator set or other apparatus to eliminate the disturbance to other customers.