Operating Temperature Sample Clauses

Operating Temperature. 8 The BBS and all components must operate without performance degradation over a 9 temperature range of -40°C to +74°C with a maximum load of 70 percent of rated output of the 10 BBS inverter.
Sample 1Sample 2Sample 3See All (6)
AutoNDA by SimpleDocs
Operating Temperature. 18 The battery system must consist of one or more strings of extreme temperature; float cycle GEL 19 valve regulated lead acid batteries. Batteries must be certified to operate at extreme 20 temperatures from –40°C to +71°C.
Sample 1Sample 2Sample 3See All (5)
Operating Temperature. 40°F to +165°F (Derating after +131°F)
Sample 1
Operating Temperature. The transceiver shall be capable of continuous operation over an ambient temperature range of ___ degrees C to ___ degrees C in still air. The tests for low temperature and high temperature are defined in MIL-STD-810E Procedure II, Methods 502.3 and 501.3 respectively.
Sample 1
Operating Temperature. The Operating Temperature range for the completed product "home safety light" to be between 0 degrees Celsius and 45 degrees Celsius.
Sample 1
Operating Temperature. The gas operating temperature is expected to be no higher than 60 degrees Farenheit. The temperature derating factor (T) will be 1.00. (See 49 C.F.R. § 192.115.)
Sample 1
Operating Temperature. Can withstand temperatures of -20c to +50c (-4F to +122F) Average Thickness: 0.6mm and minimum corner thickness of 0.5mm Fitted with: The container must incorporate a built-in carrying handle which must be a minimum of 9cm long and 3cm high, with no sharp edges. The handle is the principle means of carrying the container. The container must also incorporate a screwable cap for filling and discharge that is linked to the container by a polyamide retaining strap with diameter of min 1mm and approximately 120mm length. The inner diameter of the cap must be approximately 35mm, with the opening in the container of a corresponding size. Impact Resistance / Drop Test: The water container will be impact resistant on a hard surface when filled with the maximum volume of water (10-Liters) at 20oC. The complete drop test consists of 10 consecutive drops from 2.5m high. The water container must be elevated, so that the lowest point is at 2.5m from the ground. Test result is expressed as a product ranking according to the number of drops passed without damages or leakage. To be accepted, the water container must resist to minimum 3 drops. END OF SECTION C D - Packaging and Marking This section is Not Applicable unless the Contracting Officer amends the contract bilaterally otherwise.
Sample 1
AutoNDA by SimpleDocs

Related to Operating Temperature

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Rent Rolls; Operating Histories The Seller has obtained a rent roll (the “Certified Rent Roll(s)”) other than with respect to hospitality properties certified by the related Mortgagor or the related guarantor(s) as accurate and complete in all material respects as of a date within 180 days of the date of origination of the related Mortgage Loan. The Seller has obtained operating histories (the “Certified Operating Histories”) with respect to each Mortgaged Property certified by the related Mortgagor or the related guarantor(s) as accurate and complete in all material respects as of a date within 180 days of the date of origination of the related Mortgage Loan. The Certified Operating Histories collectively report on operations for a period equal to (a) at least a continuous three-year period or (b) in the event the Mortgaged Property was owned, operated or constructed by the Mortgagor or an affiliate for less than three years then for such shorter period of time, it being understood that for mortgaged properties acquired with the proceeds of a Mortgage Loan, Certified Operating Histories may not have been available.

  • Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.

  • Production Work The Company may use Outside Entities to perform production work outside the plant and its environs provided the Company demonstrates that it is utilizing plant equipment to the maximum extent consistent with equipment capability and customer requirements and the Company is making necessary capital investments to remain competitive in the steel business and is in compliance with Article Eleven, Section B (Investment Commitment).

  • Production Report and Lease Operating Statements Within 60 days after the end of each fiscal quarter, a report setting forth, for each calendar month during the then current fiscal year to date, the volume of production and sales attributable to production (and the prices at which such sales were made and the revenues derived from such sales) for each such calendar month from the Oil and Gas Properties, and setting forth the related ad valorem, severance and production taxes and lease operating expenses attributable thereto and incurred for each such calendar month.

  • Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.

  • Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.

  • Delivery Pressure Xxxxxx agrees to use due care and diligence to furnish gas hereunder at such uniform pressure as Seller may elect up to, but not exceeding 20 pounds per square inch gauge, and not less than 5 pounds per square inch gauge, at the "Point of Delivery". Buyer shall be responsible for the installation and operation of adequate safety equipment downstream of the Point of Delivery so as to relieve or control pressure variations within the limits described above that may, for any reason through malfunction of Seller's equipment or otherwise, occur on Buyer's side of the "Delivery Point".

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • HEATING The Hirer shall ensure that no unauthorised heating appliances shall be used on the premises when open to the public without the consent of the management committee. Portable Liquefied Propane Gas (LPG) heating appliances shall not be used.

Time is Money Join Law Insider Premium to draft better contracts faster.