Controllers. 6.1 User* must nominate Controller* where Connection Point* exceeds threshold
Controllers. Any Controller shall perform such duties and possess such powers as the Board of Directors, the Chief Executive Officer or any Vice President may from time to time prescribe.
Controllers. A controller shall also be appointed to each division. Each controller shall be responsible for the implementation of accounting policies and procedures, the installation and supervision of all accounting records, including the preparation and interpretation of financial statements, the compilation of production costs and cost distributions and the taking and valuation of physical inventories. The controller shall also be responsible for the maintenance of adequate records of authorized appropriations and the approval for payment of all checks and vouchers. The controller shall, in general, perform all duties incident to the office of controller. The foregoing shall be accomplished in a manner consistent with policies and procedures established by, for or with respect to Alcoa.
Controllers. Vehicle one, Cincinnati ground. Driver: Vehicle one at gate four would like to cross runway one eight right at taxiway alpha and proceed to the VOR. Read back of all runway holding instructions is required and must include the phrase "Hold Short", the runway's identifying number and your call sign. The “Aviation Terminology” section on page 25 lists air traffic control terms and phrases with definitions. You should know what they mean before driving on an airfield. With a little practice, radio communications are not difficult. If you are ever unsure about what the controller said, or if you don’t understand an instruction, ask the controller to repeat the communication by transmitting “SAY AGAIN” . A controller, even one who is extremely busy, would rather repeat and explain instructions than have a misunderstanding lead to a runway incursion. Don’t proceed thinking that the instructions will become clear once you drive a little farther. Advance Coordination When you contact the tower before an operation, you will receive instructions on how to proceed. Be sure you understand your Use extreme caution when you hear the phraseology “go ahead”. It is only meant for you to proceed with your message and is not to be used for any other purpose. It NEVER means to proceed in moving about, or to drive on the airfield. route, stopping points and holding positions. If you are not sure where you are going and would like turn-by-turn directions, ask the controller for “progressive” taxi instructions. FAA Guide to Ground Vehicle Operations Towered Airports FAA Guide to Ground Vehicle Operations
Controllers a) Both Parties shall be considered independent Controllers with regard to the Personal Data Processed. The Parties shall not Process Personal Data as joint Controllers.
Controllers. Description - Perform all accounting services necessary to properly maintain and report on the books and records of Client Company. Provide investor relations services. Expected Allocation Factors - 1) composite*; 2) total capitalization; 3) number of general ledger transactions; 4) number of accounts payable vouchers; 5) number of active and closed projects; and 6) number of employees.
Controllers. All controllers shall have manually reset thermal overload protection, line disconnect device, and integral start/stop push-button set. Controllers arranged for automatic or remote operation shall also be provided with Hand-Auto or Local-Remote selector switch. Exterior mounted controllers shall be mounted in watertight enclosures. For all equipment inside the hull or deckhouse the motor controllers shall be located close to the equipment unless otherwise noted. Space heaters shall be provided for all motors 10 HP and larger. Motors shall have a continuous horsepower rating in accordance with NEC, NEMA, UL, etc. Standards. Motor starters shall be across-the-line starters for 10 HP and below. Motors above 15 HP shall have reduced voltage, auto- transformer type starters with closed transition soft start. Motor starter control voltage shall be 120 volts. Remote control of motors shall be as specified on the One Line Diagram. Motors to be immersed or dipped for sealed operations.
Controllers. To provide a function test, parameter check, and inspection Humidification and maximum limit sensors To provide function test, calibration and cleaning SERVICE PLAN FEATURE COMPARISON
Controllers. 10.1 User must nominate Controller if User is not the Controller
Controllers. 2.1 Each of the Parties to this Data Sharing Agreement is an independent entity and nothing contained in this Data Sharing Agreement shall be construed to imply that there is any relationship between the Parties of partnership or of principal/agent or of employer/employee nor are the Parties hereby engaging in a joint venture and accordingly, neither of the Parties shall have any right or authority to act on behalf of the other nor to bind the other by contract or otherwise, unless expressly permitted by the terms of this Agreement;
